Keterangan
Double layer roll forming machine with 2 profiles can produce two different profile drawings, which can save more space and money compared with two different machines, the material thickness range 0.3-0.8mm or 0.12-0.4mm, material PPGI, stainless steel and galvanized steel
You can choose two different profile drawings, such as:
- Roof sheet and corrugated sheet
- Wall sheet and corrugated sheet
- Roof sheet and wall sheet
- Glazed tile and roof sheet
- Glazed tile and corrugated sheet
Double layer roll forming machine with 2 profiles can not work at the same time, one time only produce one layer profile. There is one clutch as one side of the machine, and you just move one handle wheel to make other layer profile, it takes few seconds, and the whole line only need one person to operate, it is very easy.
Profile Drawing of double layer roll forming machine with 2 profiles
Technological Process of mesin roll forming double layer dengan 2 profil
Uncoiling——Roll forming—Hydraulic cutting—Products collecting
|
Daftar Mesin
|
5 tons manual decoiler | 1 set |
| Memberi makan dengan pemandu | 1 set | |
| Mesin pembentuk gulungan utama | 1 set | |
| Kotak Kontrol PLC | 1 unit | |
| Alat pemotong hidrolik | 1 unit | |
| 2m passive table | 2 unit | |
| Suku cadang | 1 paket | |
| Penutup pengaman | 1 set |
Technical Data of mesin roll forming double layer dengan 2 profil
| Nomor | Item | Jenis unit | RF-DL |
| 1 | Ketebalan Baja | mm | 0.11-0.3mm for corrugate,0.3-0.8mm for trapezoidal sheet, Colored Steel / Galvanized Steel Coil |
| 2 | Kecepatan Pembentukan | m/mnt | 8-15 |
| 3 | Dudukan rol | berdiri | Upper layer is about 22 stations Lower layer is about 20 stations |
| 4 | Bahan Rol | mm | Baja 45#, dilapisi dengan krom |
| 5 | Shaft material and diameter | mm | Ф75 45# steel, coated with chrome |
| 6 | Tenaga Motor Utama | Kw | 7.5 |
| 7 | Daya potong hidrolik | Kw | 4 |
| 8 | Tekanan hidrolik | Mpa | 12 |
| 9 | Sumber Daya listrik | 380V, 50HZ, 3 fase | |
| 10 | Toleransi | mm | -1.5 |
| 11 | Bahan pemotongan | Cr12Mov HRC58-62 | |
| 12 | Sistem pengaturan | PLC dengan layar sentuh | |
| 13 | Berat mesin utama | T | 10T |
| Note:main motor, hydraulic station and control box is under machine frame to save place, touch screen hang over | |||
Detail tiap komposisi:
1. Uncoiler: 5 tons manual de–coiler
- Diameter bagian dalam koil: ￠460-520mm
- Max out diameter koil: ￠1250mm
- Lebar Kumparan Maks: 1250mm
2. Hidrolik Pemotongan
- Gerakan pemotongan: Mesin utama berhenti dan kemudian memotong secara otomatis. Setelah pemotongan, mesin utama akan hidup kembali secara otomatis.
- Bahan pisau: CR12Mov dengan perlakuan panas
- Pengukuran panjang: Secara otomatis
- The cutting thickness:0.5-1.0mm
- Hydraulic Station Power: 4kw
3. 2 meters passive table
Ini mengadopsi baja yang dilas dan roller yang didukung untuk mengirimkan produk.
Size: 2000*1300*800mm
4. Kotak kontrol
(1) Power supplier: 380V, 50 Hz, 3Phase
(2) Pengukuran panjang & kuantitas secara otomatis;
(3) Length & quantity controlled by PLC
(4) Ketidaktepatan panjang dapat diubah dengan mudah.
(5) Control panel: Button-type switch and touch screen
(6) Unit of length: millimeter (switched on the control panel)
Mesin Roll Forming Lapisan Ganda – Apa yang Dapat Dilakukannya Untuk Anda?
Ulasan
Belum ada ulasan.