Описание
High speed Guard Railway Crash barrier roll forming machine can make W beam guardrail, flex-beam guardrail, three wave guardrail and Box Beam Guardrail, also can be designed as two waves or three waves profiles in one machine, you just need to add some forming stations at the end of the machine according to our drawing. The guardrail’s thickness is usually 2.0mm-4mm, steel material is Q235.
Profile Drawing of High speed Guard Railway Crash barrier roll forming machine
The guardrail profile of High speed Guard Railway Crash barrier roll forming machine
Sample we made before
The production flow of equipment
Decoiling—leveling—-Punching of the sheet —— roll forming–hydraulic cut to length–out table
Список машин
|
5 tons hydraulic Un-coiler | 1 комплект |
Основная профилегибочная машина | 1 комплект | |
Feeding and leveling machine | 1 комплект | |
Hydraulic punching machine | 1 комплект | |
Гидравлическое режущее устройство | 1set | |
Пресс-формы | 2 комплекта | |
Блок управления | 1 блок | |
вне стола | 2 единицы | |
Гидравлическая станция | 1 блок |
Состав оборудования
1. 5T Hydraulic de-coiler
- Single unrolling machine, one side can put material
- Принять автоматическую гидравлическую систему
- Вес рулона (макс.): 5000 кг
- Inner diameter:460-520mm
- Coil dia (Max):1300mm
- Диаметр масляного цилиндра: 1200 мм, рабочее давление: 10 МПа.
- Ширина катушки (макс.): 500 мм
- Working speed: about 0-25m/min
- Мощность: 4кВт
2. Leveling
Main features of the machine:
The leveling roller’s mechanical property such as rigidity and roughness concentration of the surface are rising very much after hardening and tempering. It includes pinch roll and leveling roll. The pinch roll can adjust along. The leveling roll uses the whole structure. There are two adjusting point at the front and the end. It can form a certain banked angle to improve the leveling quality. The feeding port of the leveling machine has a pair of guide plain-barrelled roll and two pairs of guide vertical roll. The guide vertical roll can moves centered or moves at the same time. It is adjusted by hand wheel, so it is convenient to centered.
- Подача листа на направляющий ролик (он регулируется вправо и влево).
- Feeding roller: diameter is ¢160mm; material is 40CR steel, HRC48-52.
- Leveling roller: upper is 3 rollers, down is 4 stations(total is 7 stations), material is 40CR steel, HRC48-52.
- Диаметр выравнивающего ролика: 180 мм.
3. Hydrulic Punching
- Using hydraulic punching
- Oil cylinder dia: ¢180mm
- Рабочее давление: 30 МПа
- Mould material: Cr12 quenched 58°-62°
- Гидравлическая мощность: 7,5 кВт
- Size: 1.5m long*1.1m wide*1.2m high
4. High speed Guard Railway Crash barrier roll forming machine
- Мощность главного двигателя: 22 кВт
- Станция: принять чугун HT50
- Decelerating motor: made in Shanghai or Changzhou
- Drive: Gear box driving
- Main shaft dia:¢120mm, material: 45﹟forge steel
- Roller material: GCR15 quenched 58°-62°,chromed
- Roll station: about 15 stations
- Material thickness: 2.5-4.0mm
- Machine speed: about 3-5m/min
- Power supply: 380V 50HZ, 3 phases
- Control system: PLC with touch screen
5. Hydraulic cutting
- Гидравлическая резка
- Knife material: Cr12Mov,quenched 58°-62°
- Диаметр масляного цилиндра: 250 мм
- Рабочее давление: 60 МПа
- Рабочий путь: 80мм
6. Control box
- Full line is controlled by PLC control system, touch screen operation to achieve the human and PLC interactive.
- Operation type: manual /auto two type switch. In manual position: can run the each part of the machine.
- Источник питания: 380 В, 50 Гц, 3 фазы (регулируется по запросу)
- Автоматическое измерение длины и количества;
- Длина и количество контролируется ПЛК
- Неточность длины можно легко исправить.
- Панель управления: кнопочный переключатель и сенсорный экран
- Единица длины: миллиметр (включается на панели управления)
Отзывы
Отзывов пока нет.